hallo kann mir jemand von euch vielleicht die deutschen nemen für die instrument in den "text" einsetzten ?
das würde mir die arbeit erheblich erleichtern danke euch schonmal im voraus
grüßle lars
;Name Var Title Units Lo Hi LoD LoW HiW HiD vd ld
advBucketGauge = veTuneValue, "Advance Bucket", "degrees", 0, 55, -1, -1, 999, 999, 1, 1
advdegGauge = advance, "Ignition Advance", "degrees", 5, 50, -1, -1, 999, 999, 1, 1
IACgauge = iacstep, "IAC position", "steps", 0, 255, -1, -1, 999, 999, 0, 0
dwellGauge = dwell, "Dwell", "mSec", 0, 10, 0.5, 1.0, 6.0, 8.0, 1, 1
; IAC step == idle pwm, when using pwm idle control.
PWMIdlegauge = idleDC, "Idle PWM%", "%", 0, 100, -1, -1, 999, 90, 0, 0
accelEnrichGauge = accDecEnrich, "Accel Enrich", "%", 50, 150, -1, -1, 999, 999, 0, 0
afr1Gauge = afr1, "Air:Fuel Ratio", "", 10, 19.4, 12, 13, 15, 16, 2, 2
afr2Gauge = afr2, "Air:Fuel Ratio 2", "", 10, 19.4, 12, 13, 15, 16, 2, 2
clockGauge = seconds, "Clock", "Seconds", 0, 255, 10, 10, 245, 245, 0, 0
deadGauge = deadValue, "---", "", 0, 1, -1, -1, 2, 2, 0, 0
dutyCycle1Gauge = dutyCycle1, "Duty Cycle 1", "%", 0, 100, -1, -1, 85, 90, 1, 1
dutyCycle2Gauge = dutyCycle2, "Duty Cycle 2", "%", 0, 100, -1, -1, 85, 90, 1, 1
egoCorrGauge = egoCorrection, "EGO Correction", "%", 50, 150, 90, 99, 101, 110, 0, 0
egoCorrGauge1 = egoCorrection1,"EGO Correction 1", "%", 50, 150, 90, 99, 101, 110, 0, 0
egoCorrGauge2 = egoCorrection2,"EGO Correction 2", "%", 50, 150, 90, 99, 101, 110, 0, 0
egoGauge = egoVoltage, "Exhaust Gas Oxygen", "volts", 0, 1.0, 0.2, 0.3, 0.7, 0.8, 2, 2
kpabaroGauge = kpaix, "Engine MAP/baro", "kPa", 0, 255, 0, 20, 200, 245, 1, 0
knockGauge = knockRetard "Knock Retard", "deg", 0, 25.0, -1, -1, 5.0, 10.0, 1, 1
lambda1Gauge = lambda1, "Lambda", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2
lambda2Gauge = lambda2, "Lambda", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2
gammaEnrichGauge = gammaEnrich, "Gamma Enrichment", "%", 50, 150, -1, -1, 151, 151, 0, 0
mapGauge = map, "Engine MAP", "kPa", 0, 255, 0, 20, 200, 245, 1, 0
mafGauge = maf, "MAF Air flow", "g/sec", 0, 650, 0, 200, 480, 550, 0, 0
barometerGauge = barometer, "Barometer", "kPa", 60, 120, 0, 20, 200, 245, 1, 0
calcMapGauge = calcMAP, "Estimated MAP", "kPa", 0, 255, 0, 20, 200, 245, 1, 0
pulseWidth1Gauge = pulseWidth1, "Pulse Width 1", "mSec", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1
pulseWidth2Gauge = pulseWidth2, "Pulse Width 2", "mSec", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1
tachometer = rpm, "Engine Speed", "RPM", 0, 8000, 300, 500, 5000, 6000, 0, 0
throttleGauge = throttle, "Throttle Position", "%", 0, 100, -1, 1, 90, 100, 0, 0
; timmingErrGauge = timingErr, "Timing Error", "degrees",-10, 10, -10, -5, 5, 10, 1, 1
deltaTGauge = deltaT, "Timing Delta", "uS", 0, 25000, 0, 0,25000, 25000, 0, 0
veBucketGauge = veTuneValue, "VE Value", "%", 0, 120, -1, -1, 999, 999, 0, 0
veGauge = veCurr1, "VE Current", "%", 0, 120, -1, -1, 999, 999, 0, 0
voltMeter = batteryVoltage, "Battery Voltage", "volts", 7, 21, 9, 10, 16, 17, 2, 2
warmupEnrichGauge = warmupEnrich, "Warmup Enrichment", "%", 100, 150, -1, -1, 101, 105, 0, 0
; Name Var Title Units Lo Hi LoD LoW HiW HiD vd ld
xTauGauge1 = xTauFuelCorr1, "X-Tau Correction1", "%", 0, 200, 40, 70, 130, 160, 0, 0
xTauGauge2 = xTauFuelCorr2, "X-Tau Correction2", "%", 0, 200, 40, 70, 130, 160, 0, 0
#if CELSIUS
#if EXPANDED_CLT_TEMP
cltGauge = coolant, "Coolant Temp", "C", -40, 600, 65, 93, 162, 176, 0, 0
matGauge = mat, "Intake Air Temp", "C", -40, 110, -15, 0, 95, 100, 0, 0
#else
cltGauge = coolant, "Coolant Temp", "C", -40, 120, -15, 0, 95, 105, 0, 0
matGauge = mat, "Intake Air Temp", "C", -40, 110, -15, 0, 95, 100, 0, 0
#endif
#else
#if EXPANDED_CLT_TEMP
cltGauge = coolant, "Coolant Temp", "?F", -40, 600, 150, 200, 325, 350, 0, 0
matGauge = mat, "Intake Air Temp", "?F", -40, 215, 0, 30, 200, 210, 0, 0
#else
cltGauge = coolant, "Coolant Temp", "?F", -40, 250, 0, 30, 200, 220, 0, 0
matGauge = mat, "Intake Air Temp", "?F", -40, 215, 0, 30, 200, 210, 0, 0
#endif
#endif
e85Gauge = fuelCorrection,"E85 Fuel Correction", "%", 100, 200, 99, 99, 164, 170, 0, 0
ethanolGas = fuelComposition, "Ethanol Percentage","%", 0, 100, -1, -1, 85, 101, 0, 0
triggers± = trig_fix, "Triggers add/sub", "", -200, 200, -100, -10, 10, 100, 0, 0
tachCount = tachCount, "Number Tach Pulses", "", 0, 1000, -1, -1, 1000, 1000, 0, 0
Anzeigen in Deutsch
Re: Anzeigen in Deutsch
Wo finde ich die Texte damit ich die mal eindeutschen kann?
Gruß Frank
Elise mit MS3 und Spartan
(ex RS2000 16v mit UMC1/ MSextra V3.4.1 und Lamda von Knödler)
Elise mit MS3 und Spartan
(ex RS2000 16v mit UMC1/ MSextra V3.4.1 und Lamda von Knödler)
Re: Anzeigen in Deutsch
Hallo die findest du in der megasquirtxx.ini xx steht für version
Mein text ist der auszug draus der um die anzeige geht muss mir eh noch eine für den tachoo bauen
Mein text ist der auszug draus der um die anzeige geht muss mir eh noch eine für den tachoo bauen